Page 3 of 3

Re: Amiga 600 FPGA (MiSTer) Conversion

Posted: Tue Oct 22, 2019 3:30 am
by DazzaS
This is awesome...

Purchased a DE10 to play some old games and was looking around for a nice retro like case to print then found Matt's Amiga 600 MiSTer build.

After that there was just no other choice I had to have one of these for myself. :mrgreen:

Here is a happy snap of my final prints laid out in A600 base, the fit up is a testament to Matt's attention to detail.

Image

BTW if you are going to print Matt's Amiga 600 MiSTer build be sure to print up a larger calibration cube to ensure printer accuracy, millimetres matter on this one.

Re: Amiga 600 FPGA (MiSTer) Conversion

Posted: Thu Nov 07, 2019 2:39 am
by MattSwe
This is great! I'm getting inspired and I will try to use this in a new project.

DazzaS: Did you print this in one whole piece or are the joints just invisible? :)

Re: Amiga 600 FPGA (MiSTer) Conversion

Posted: Fri Nov 08, 2019 4:39 am
by DazzaS
MattSwe wrote:
Thu Nov 07, 2019 2:39 am
DazzaS: Did you print this in one whole piece or are the joints just invisible? :)
Hi MattSwe,

Would nice to be have a 3D printer with a build volume to handle monster prints but alas print is true to Mattsoft's original design so 6 individual parts in 5 prints not including the oversized ones due to printer calibration :roll:

Here is a happy snap of all the prints with some accessories fitted.

Image

Here is a quick BOM of the parts I have so far not including DE10 and MiSTer v6.0 I/O board.

1x DC Power Supply Jack Socket Female Panel Mount Connector 5.5 x 2.1mm, Fitting hole of 7.8mm with rear locking nut.
1x Mini Panel Mount Switch 3A 250V ON-OFF SPST Dimensions 15x10x17mm Mounting Hole 14x9mm.
1x 8mm Mini Waterproof Car Momentary Push Button Switch Zinc-Aluminium *This one differs to Matt's.
1x Adafruit Panel mount HDMI Cable 40cm part number ADA978, *This is a perfect fit.
2x SparkFun USB Type A Female Breakout part number BOB-12700
1x Micro SD TO Micro SD Card Extension Cable Adaptor Extender
1x Heatsink with 3m tape for DE10 FPGA Dimensions 22x22x10mm
1x Adafruit ZERO4U 4-PORT USB HUB without POGO pins v1.3 part number ADA4115
1x Micro USB B Male to Mini USB B Male Data Cables Digital Cables Cord OTG Adapter


I am still looking at MiSTer Memory and Keyboard adaptor options.

DazzaS

Re: Amiga 600 FPGA (MiSTer) Conversion

Posted: Mon Nov 11, 2019 11:37 am
by mattsoft
3D-vice wrote:
Mon Sep 02, 2019 9:49 am
That is a pretty neat project, Matt!

I'd like to ask a 3D-print related question: Was it hard to get all of those measurements done? Or did you use any kind of 3D-scanner? The reason I ask is because I have an unfinished Rhaspberry-PI C64 project and IF I ever continue working on it, I'll need to 3D-print a bunch of adapters too.

Thanks in advance! :)
Calipers and a ruler and lots and lots of prototypes. :)

Re: Amiga 600 FPGA (MiSTer) Conversion

Posted: Sat Dec 14, 2019 7:52 am
by Tekk
Can you design a solution with the memory card in the disk slot for the A500 project as well? Cheers... :)

Re: Amiga 600 FPGA (MiSTer) Conversion

Posted: Sat Feb 15, 2020 3:06 am
by ikklepaul
mattsoft,

Wow these look great, i'm considering doing the same with an old Amiga 1200 case and keyboard.

You don't by chance have any 3d models for the A1200 do you?

Keep up the great work :D

Re: Amiga 600 FPGA (MiSTer) Conversion

Posted: Fri Mar 27, 2020 6:29 am
by MattSwe
I hope you guys think this is OK. ;) All I can say is that I've had so much fun with this and I wanted to show you. The excellent build by mattsoft made it possible.

Image

What are we looking at? :) Yes, it's a NUC instead of a MiSTer. It's USB3 and RJ45 and a ventilation grille. It works really well and runs cooler than expected. It loads straight into WinUAE (all visual Windows elements removed).

I don't own a 3D printer, so I had it printed out for me and the alterations were made using "analogue" tools. :D The black A600 case was bought on eBay.

Thank you, mattsoft.

Re: Amiga 600 FPGA (MiSTer) Conversion

Posted: Fri May 08, 2020 4:19 am
by alexatkin
Is anyone in the UK and able to print these parts for me?

I can't think of any other way I'm going to get it done during the lock down, plus I figure anyone who has already done it will already have the calibration sorted.