User avatar
acolic

Posted Tue May 12, 2020 9:25 pm

For now the 2090a is toast. Two pins from the SCSI header on the motherboard are missing.

So it’s back to the dataflyer.

I see online their are dms install files for it. I guess that’s some sort of Amiga disk image.

I have a windows laptop with a 3 1/4 drive in it.

I hope theirs an app that can format and write the dms file.

All I want to do is find out what is Imon the hard drive.

User avatar
acolic

Posted Sat Jun 20, 2020 10:25 pm

Ok the 3.14 Rom chips, the USB drive and the SCSI2SD card arrived.

I have the Rom installed and the ADF images installed on the USB drive. All ok I can boot into 3.14.

Now I want to install 3.14 to the SD card and boot from my HD.

So I attached the SCSI2SD card to my 2090A, started the machine and nothing.

I also tried the Dataflyer controller. Nothing.

I must be missing something.

Any help appreciated.

Alex

Am I supposed to format the SD card on a PC first?

I used the checkconfig tool and the card was identified. I tried the format tool and the only thing recognized was DF0.

User avatar
McTrinsic

Posted Sun Jun 21, 2020 3:49 am

The 2090a is a bit non-Standard.

Check some online resources for installing AmigaOS on HD - it is completely different to how it works on a PC.

You need to configure the SD via the driver here:

https://amiga.resource.cx/search.pl?id=a2090a

User avatar
acolic

Posted Sun Jun 21, 2020 2:26 pm

Hi

I spend most of the day and it has not gone well.


Some times the SCSI2SD is recognized, some times it is not.

Is there a modern Amiga SCSI adapter out there?

Thanks

Alex

User avatar
McTrinsic

Posted Mon Jun 22, 2020 2:18 am

Could you a bit more I to detail what you did?

Would be interested to see what we can do about this.

How did you
- set termination
- provide power to the SCSI2SD
?

User avatar
McTrinsic

Posted Mon Jun 22, 2020 2:20 am

And to answer your question: no newer SCSI that I’m aware of.

You might want to consider IDE:
https://icomp.de/shop-icomp/en/shop/pro ... a-ide.html

User avatar
Zippy Zapp
CA, USA

Posted Mon Jun 22, 2020 9:57 am

I use the SCSI2SD a lot in classic Macs it is a great device but you have to configure it first. You can download the utility and the instructions at the SCS2SD site.

Sorry if you have tried that already but just in case you didn't.

User avatar
acolic

Posted Sun Jul 26, 2020 2:43 pm

McTrinsic wrote:
Mon Jun 22, 2020 2:18 am
Could you a bit more I to detail what you did?

Would be interested to see what we can do about this.

How did you
- set termination
- provide power to the SCSI2SD
?
Hi

I had some time to work on this.

I managed to hook up the SCSI2Sd card to my computer and using the SCSI2SD-util program I updated the firmware and created one 2gig partition.

I then hooked the card up to my Dataflyer scsi card and booted with a 3.14 install disk. I tried hdtools but it did not recognize the hard drive. I booted from a dataflyer install disk same thing it did not recognize the HD.

Power is being provided by a floppy power source.

I can’t see a way to terminate the HD. It’s the only HD in the computer.

Any suggestions?

Thanks

Alex

User avatar
McTrinsic

Posted Wed Jul 29, 2020 4:43 am

I am under the impression that with ‚HDD‘ you mean the SD in the SCSI2SD.

The SCSI2SD has two (yellow?) resistors on it with like 10 pins each. They can be removed.

If it’s the only mass storage on the SCSI line it needs to have the resistors in. Then the SCSI2SD is terminated.

Please check the DataFlyer manual on how to set termination on that adapter.





Return to “Member Intros”